One good repeater on a hill does more for a local mesh than anything else. With solar power it keeps running when the grid fails – exactly when a mesh is most useful. The tropics are harder on hardware than Europe: heat all year, high humidity, monsoon rain, salty air and thunderstorms. This page collects what matters.
1. Choose a low-power board
A repeater listens all the time, so idle power decides the size of panel and battery.
- nRF52 boards (e.g. RAK4631, T-Echo, SenseCAP Solar Node) need very little power and are the best choice for solar.
- ESP32 boards (e.g. Heltec V3, LilyGo LoRa32) draw many times more. They work, but need a much bigger panel and battery.
- Prefer an SX1262 radio with TCXO – an accurate crystal matters in the heat with the narrow 62.5 kHz profile.
- Buy the 915 MHz version for Thailand and Vietnam (see Frequencies).
Ready-made option: the SenseCAP Solar Node (Seeed) comes with panel, battery holder and weatherproof case and is supported by the MeshCore flasher.
2. Panel and battery
Rule of thumb: plan for one to two weeks without sun – in the rainy season it can be grey for days.
- Calculate the daily energy of your board (average current × voltage × 24 h) and multiply by the number of cloudy days you want to bridge. That is your usable battery capacity.
- The panel should refill a day’s use plus losses in a few hours of good sun. Tropical sun is strong, but rainy-season days are short on it – size generously.
- Battery chemistry: LiFePO4 handles heat much better than normal lithium-ion and lives longer. If you use 18650 Li-ion cells, buy quality cells and keep them shaded.
- Lithium batteries should not be charged when very hot – good charge controllers stop charging above a set temperature. Check that yours does.
3. Heat
- A dark box in full sun easily reaches 60–70 °C inside.
- Use a light-coloured or white enclosure, give it shade (a small roof or mount it under the panel), and keep the battery away from the panel’s hot back side.
- Heat is the main reason batteries age – shade is the cheapest upgrade.
4. Humidity, rain and salt air
- Use an IP65/IP67 enclosure with sealed cable glands.
- Add a pressure-equalising vent (Gore-type membrane) – without it the box “breathes” through the seals and collects condensation.
- Put silica gel inside and replace it after the rainy season.
- Seal antenna connectors with self-amalgamating tape. Near the sea, use stainless steel hardware; salt air corrodes everything else.
- Insects and geckos love warm boxes – close every opening.
5. Antenna
- The antenna matters more than the board. Use one made for 915/920 MHz – an 868 MHz antenna works badly here.
- Height wins: line of sight decides the range. A few metres above the roof edge make a big difference.
- High-gain collinear antennas (the long white fibreglass ones) send the signal flat to the horizon – great from a hilltop, but a valley directly below a steep hill can get weaker coverage.
- Gain counts towards the legal limit (EIRP = transmit power + antenna gain). With a high-gain antenna, lower the transmit power accordingly.
6. Lightning
Thunderstorms in the rainy season are severe.
- Ground the mast and use a coax surge arrester at the point where the cable enters a building.
- Don’t make the repeater the highest point of a roof without protection.
- On a hilltop, assume a strike will eventually happen – a cheap, easily replaceable node is better than an expensive one.
7. Configure it
- Flash Repeater firmware with the MeshCore flasher.
- Set the radio profile of your country (Thailand: 920.250 MHz / BW 62.5 / SF 8 / CR 5).
- Set the MeshCore regions of your area (e.g.
thandth-phuket) – see Regions and your region page. - Give it a clear name with your location code, e.g.
HKT Big Buddha Repeater, and set its position so it shows up on the map. - Upload it to the MeshCore map – then it appears on meshcore.asia too.
8. Location and maintenance
- Ask for permission – a café, hotel or house on a hill often agrees, especially if the repeater carries its name.
- Check the planned coverage first with a tool like Meshtastic Site Planner (works for any LoRa device) or HeyWhatsThat.
- Check it twice a year, ideally after the rainy season: silica gel, seals, connectors, battery.
Experience from Switzerland
A SenseCAP Solar Node P1-Pro with a large collinear antenna on a forested mountain covers a whole canton and survived a summer heatwave with around 40 °C in full sun. The tropics add humidity, salt and monsoon on top – but heat alone is not a show-stopper for good hardware.
Have you built a repeater in Asia? Share your experience: [email protected]