One good repeater on a hill does more for a local mesh than anything else. With solar power it keeps running when the grid fails – exactly when a mesh is most useful. The tropics are harder on hardware than Europe: heat all year, high humidity, monsoon rain, salty air and thunderstorms. This page collects what matters.

1. Choose a low-power board

A repeater listens all the time, so idle power decides the size of panel and battery.

  • nRF52 boards (e.g. RAK4631, T-Echo, SenseCAP Solar Node) need very little power and are the best choice for solar.
  • ESP32 boards (e.g. Heltec V3, LilyGo LoRa32) draw many times more. They work, but need a much bigger panel and battery.
  • Prefer an SX1262 radio with TCXO – an accurate crystal matters in the heat with the narrow 62.5 kHz profile.
  • Buy the 915 MHz version for Thailand and Vietnam (see Frequencies).

Ready-made option: the SenseCAP Solar Node (Seeed) comes with panel, battery holder and weatherproof case and is supported by the MeshCore flasher.

2. Panel and battery

Rule of thumb: plan for one to two weeks without sun – in the rainy season it can be grey for days.

  • Calculate the daily energy of your board (average current × voltage × 24 h) and multiply by the number of cloudy days you want to bridge. That is your usable battery capacity.
  • The panel should refill a day’s use plus losses in a few hours of good sun. Tropical sun is strong, but rainy-season days are short on it – size generously.
  • Battery chemistry: LiFePO4 handles heat much better than normal lithium-ion and lives longer. If you use 18650 Li-ion cells, buy quality cells and keep them shaded.
  • Lithium batteries should not be charged when very hot – good charge controllers stop charging above a set temperature. Check that yours does.

3. Heat

  • A dark box in full sun easily reaches 60–70 °C inside.
  • Use a light-coloured or white enclosure, give it shade (a small roof or mount it under the panel), and keep the battery away from the panel’s hot back side.
  • Heat is the main reason batteries age – shade is the cheapest upgrade.

4. Humidity, rain and salt air

  • Use an IP65/IP67 enclosure with sealed cable glands.
  • Add a pressure-equalising vent (Gore-type membrane) – without it the box “breathes” through the seals and collects condensation.
  • Put silica gel inside and replace it after the rainy season.
  • Seal antenna connectors with self-amalgamating tape. Near the sea, use stainless steel hardware; salt air corrodes everything else.
  • Insects and geckos love warm boxes – close every opening.

5. Antenna

  • The antenna matters more than the board. Use one made for 915/920 MHz – an 868 MHz antenna works badly here.
  • Height wins: line of sight decides the range. A few metres above the roof edge make a big difference.
  • High-gain collinear antennas (the long white fibreglass ones) send the signal flat to the horizon – great from a hilltop, but a valley directly below a steep hill can get weaker coverage.
  • Gain counts towards the legal limit (EIRP = transmit power + antenna gain). With a high-gain antenna, lower the transmit power accordingly.

6. Lightning

Thunderstorms in the rainy season are severe.

  • Ground the mast and use a coax surge arrester at the point where the cable enters a building.
  • Don’t make the repeater the highest point of a roof without protection.
  • On a hilltop, assume a strike will eventually happen – a cheap, easily replaceable node is better than an expensive one.

7. Configure it

  • Flash Repeater firmware with the MeshCore flasher.
  • Set the radio profile of your country (Thailand: 920.250 MHz / BW 62.5 / SF 8 / CR 5).
  • Set the MeshCore regions of your area (e.g. th and th-phuket) – see Regions and your region page.
  • Give it a clear name with your location code, e.g. HKT Big Buddha Repeater, and set its position so it shows up on the map.
  • Upload it to the MeshCore map – then it appears on meshcore.asia too.

8. Location and maintenance

  • Ask for permission – a café, hotel or house on a hill often agrees, especially if the repeater carries its name.
  • Check the planned coverage first with a tool like Meshtastic Site Planner (works for any LoRa device) or HeyWhatsThat.
  • Check it twice a year, ideally after the rainy season: silica gel, seals, connectors, battery.

Experience from Switzerland

A SenseCAP Solar Node P1-Pro with a large collinear antenna on a forested mountain covers a whole canton and survived a summer heatwave with around 40 °C in full sun. The tropics add humidity, salt and monsoon on top – but heat alone is not a show-stopper for good hardware.

Have you built a repeater in Asia? Share your experience: [email protected]